(old)Puppy Linux Discussion Forum

Posted: **Mon 30 Mar 2020, 20:52**

I 'm trying to connect to internet but I can't.
I tried with Puppy 5.6 and with BionicPup32, the result is the same.

Recently I changed to a new internet provider.
With my previous I could connect without problem (using puppy linux).
In windows I face no problem.

This is my log file:

Information about this interface:
Interface: wlan0 Driver: rt73usb Bus: usb MacAddress: 00:1B:FC:F0:F1:17
Description: Ralink RT73 USB Wireless LAN driver.

STEP1a: ifconfig wlan0 up
STEP1b: iwlist wlan0 scan
wlan0 Scan completed :

Cell 02 - Address: C0:FD:84:DE:D1:4B
Channel:10
Frequency:2.457 GHz (Channel 10)
Quality=56/70 Signal level=-54 dBm
Encryption key:on
ESSID:"********"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000000c8e7d1fda4
Extra: Last beacon: 63ms ago
IE: Unknown: 000A4E6F76612D4670463961
IE: Unknown: 010882848B960C121824
IE: Unknown: 03010A
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: Unknown: 2D1A0E181FFFFF000000000000000000000000000000000000000000
IE: Unknown: 3D160A070000000000000000000000000000000000000000
IE: WPA Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C330E181FFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C340A070000000000000000000000000000000000000000
IE: Unknown: DD0600E04C020160
IE: Unknown: DD900050F204104A0001101044000102103B00010310470010630412531019200612284144534C204D1021000F5A544520436F72706F726174696F6E1023000A5A58484E20483130384E1024000A5A58484E20483130384E1042000F3132333435363738393031323334371054000800060050F2040001101100114144534C204D6F64656D2F526F75746572100800020080

STEP1c: ifconfig wlan0 down
STEP2: iwconfig wlan0 mode managed
STEP3: iwconfig wlan0 channel 10
Error for wireless request "Set Frequency" (8B04) :
SET failed on device wlan0 ; Network is down.
STEP4: iwconfig wlan0 essid "Nova-FpF9a"
STEP5a: ifconfig wlan0 up
STEP5b: wpa_supplicant -B -Dwext -iwlan0 -c"/etc/simple_network_setup/wpa_supplicant.conf-Nova-FpF9a-00:1B:FC:F0:F1:17"
STEP6a: dhcpcd wlan0
dhcpcd[380]: version 5.5.6 starting
dhcpcd[380]: all: not configured to accept IPv6 RAs
dhcpcd[380]: wlan0: waiting for carrier
dhcpcd[380]: timed out
dhcpcd[380]: allowing 8 seconds for IPv4LL timeout
dhcpcd[380]: timed out
STEP6b: dhcpcd -I '' wlan0
dhcpcd[1926]: version 5.5.6 starting
dhcpcd[1926]: all: not configured to accept IPv6 RAs
dhcpcd[1926]: wlan0: waiting for carrier
dhcpcd[1926]: timed out
dhcpcd[1926]: allowing 8 seconds for IPv4LL timeout
dhcpcd[1926]: timed out

*********************************************************
LAST 10 LINES of /var/log/messages:
Mar 31 14:32:29 puppypc9573 user.info kernel: [ 870.540711] cfg80211: Calling CRDA to update world regulatory domain
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.913532] wlan0: authenticate with c0:fd:84d1:4b
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.951327] wlan0: send auth to c0:fd:84d1:4b (try 1/3)
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.952831] wlan0: authenticated
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.973258] wlan0: associate with c0:fd:84d1:4b (try 1/3)
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.975702] wlan0: RX AssocResp from c0:fd:84d1:4b (capab=0x411 status=0 aid=4)
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.986576] wlan0: associated
Mar 31 14:32:30 puppypc9573 user.debug kernel: [ 871.989831] wlan0: disassociated from c0:fd:84d1:4b (Reason: 14)
Mar 31 14:32:30 puppypc9573 user.info kernel: [ 872.023965] cfg80211: Calling CRDA to update world regulatory domain
Mar 30 23:32:31 puppypc9573 daemon.err dhcpcd[3473]: dhcpcd not running

*********************************************************
LAST 10 LINES of /var/log/messages:

Any help is welcome.[/quote]

Posted: **Mon 30 Mar 2020, 21:57**

Down at the bottom there where it gives reason 14 as a dissociate reason has to do with TKIP failure.

It might help to make sure your WPA algorithm is set to AES.

Posted: **Tue 31 Mar 2020, 08:56**

The option I have for encryption is:
-none
-WEP-
-WPA

In WPA I cannot see ane 'AES' option.

Posted: **Tue 31 Mar 2020, 10:40**

Now it works(!!), I don't know why.
O hope it 'll be ok.

Posted: **Tue 31 Mar 2020, 16:32**

CCMP is the same thing as AES

WPA is better than WEP

WEP is easy for a hacker to break.

WPA2 is better than WPA1
WPA3 is better than WPA2

If wifi is configured without specifying what to use,
the wifi should connect using the best encryption method.

Normally, you would choose CCMP, WPA2, and PSK is the password (pass key)

You can see how you are connected by typing in a console terminal:

Code: Select all

wpa_cli status

It will also tell you your IP address.
If there is no ip_address= you are not connected.(which is often a dhcpc problem)

(old)Puppy Linux Discussion Forum

Cannot connect to internet

Cannot connect to internet