[OPEN] 4.2.1 Network config not loading
[OPEN] 4.2.1 Network config not loading
4.2.1 frugal USB. Wifi Network configuration previously set up does not autoload at next boot and has to be set up via the wizard again.
Spup Frugal HD and USB
Root forever!
Root forever!
Re: [Bug] 4.2.1 Network config not loading
Same story with me on a frugal HD install. Was ok with 4.2.0.DaveS wrote:4.2.1 frugal USB. Wifi Network configuration previously set up does not autoload at next boot and has to be set up via the wizard again.
Mike
Re: [Bug] 4.2.1 Network config not loading
Could this be because your pup_save file isn't created until you reboot? I don't know where these settings are stored in the RAM disk, but maybe that section isn't getting saved on first creation of the pup_save. Does it save ok for subsequent boots following creation of the pup_save file?DaveS wrote:4.2.1 frugal USB. Wifi Network configuration previously set up does not autoload at next boot and has to be set up via the wizard again.
[i]Actions speak louder than words ... and they usually work when words don't![/i]
SIP:whodo@proxy01.sipphone.com; whodo@realsip.com
SIP:whodo@proxy01.sipphone.com; whodo@realsip.com
log
This is my bootsysinit log from a cold boot, hope it helps with debugging.
VERSION UPDATE
LOAD KERNEL MODULES
LOAD SWAP
MISC. SYSTEM SETUP
WAIT MODULES LOADED
ls: cannot access /sys/bus/pcmcia/devices/*/modalias: No such file or directory
USER SELECTED MODULES
SETUP SERVICES
RECOGNISE MEDIA DEVICES
Waiting for interfaces to initialize...
Loading "uk" keyboard map... Loading /usr/share/kbd/keymaps/i386/qwerty/uk.map
configuring network interface eth0
interface eth0 has not been configured... skipping
configuring network interface wlan0
/etc/rc.d/rc.network: line 208: checkIsPCMCIA: command not found
MISC. DESKTOP STUFF
PERSONAL BOOT SCRIPT
-> Projectfiles.com Linux Firewall version 2.0rc9 running.
-> Performing sanity checks...... [ PASSED ]
-> Building firewall.... [ DONE ]
/etc/rc.d/rc.network: line 493: Get_Cell_Parameters: command not found
/etc/rc.d/rc.network: line 576: Get_Cell_Parameters: command not found
Configuring interface wlan0 to network with iwconfig...
cheching if interface wlan0 is alive...yes
cups: started scheduler.
ACPI Power Button support enabled.
acpi daemon started.
Starting PCMCIA services:
Success!
lease
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
Debug, wlan0: waiting on select for 20 seconds
3
6
9
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
12
15
18
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
21
24
27
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
30
33
36
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
39
42
45
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
48
51
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
54
57
Error, wlan0: timed out
Info, wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Error, wlan0: lease information file `/var/lib/dhcpcd/dhcpcd-wlan0.info' does not exist
Info, wlan0: probing for an IPV4LL address
Debug, wlan0: sending ARP probe #1
60
Debug, wlan0: sending ARP probe #2
Debug, wlan0: sending ARP probe #3
Debug, wlan0: sending ARP claim #1
Debug, wlan0: sending ARP claim #2
Warning, wlan0: using IPV4LL address 169.254.52.160
Info, wlan0: adding IP address 169.254.52.160/16
Debug, wlan0: no dns information to write
Debug, wlan0: writing /var/lib/dhcpcd/dhcpcd-wlan0.info
Debug, wlan0: exec "/etc/dhcpcd.sh" "/var/lib/dhcpcd/dhcpcd-wlan0.info" "new"
Debug, wlan0: forking to background
100
63
66
69
72
75
78
81
84
87
90
VERSION UPDATE
LOAD KERNEL MODULES
LOAD SWAP
MISC. SYSTEM SETUP
WAIT MODULES LOADED
ls: cannot access /sys/bus/pcmcia/devices/*/modalias: No such file or directory
USER SELECTED MODULES
SETUP SERVICES
RECOGNISE MEDIA DEVICES
Waiting for interfaces to initialize...
Loading "uk" keyboard map... Loading /usr/share/kbd/keymaps/i386/qwerty/uk.map
configuring network interface eth0
interface eth0 has not been configured... skipping
configuring network interface wlan0
/etc/rc.d/rc.network: line 208: checkIsPCMCIA: command not found
MISC. DESKTOP STUFF
PERSONAL BOOT SCRIPT
-> Projectfiles.com Linux Firewall version 2.0rc9 running.
-> Performing sanity checks...... [ PASSED ]
-> Building firewall.... [ DONE ]
/etc/rc.d/rc.network: line 493: Get_Cell_Parameters: command not found
/etc/rc.d/rc.network: line 576: Get_Cell_Parameters: command not found
Configuring interface wlan0 to network with iwconfig...
cheching if interface wlan0 is alive...yes
cups: started scheduler.
ACPI Power Button support enabled.
acpi daemon started.
Starting PCMCIA services:
Success!
lease
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
Debug, wlan0: waiting on select for 20 seconds
3
6
9
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
12
15
18
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
21
24
27
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
30
33
36
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
39
42
45
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
48
51
Debug, wlan0: sending DHCP_DISCOVER with xid 0x6dae6357
54
57
Error, wlan0: timed out
Info, wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Error, wlan0: lease information file `/var/lib/dhcpcd/dhcpcd-wlan0.info' does not exist
Info, wlan0: probing for an IPV4LL address
Debug, wlan0: sending ARP probe #1
60
Debug, wlan0: sending ARP probe #2
Debug, wlan0: sending ARP probe #3
Debug, wlan0: sending ARP claim #1
Debug, wlan0: sending ARP claim #2
Warning, wlan0: using IPV4LL address 169.254.52.160
Info, wlan0: adding IP address 169.254.52.160/16
Debug, wlan0: no dns information to write
Debug, wlan0: writing /var/lib/dhcpcd/dhcpcd-wlan0.info
Debug, wlan0: exec "/etc/dhcpcd.sh" "/var/lib/dhcpcd/dhcpcd-wlan0.info" "new"
Debug, wlan0: forking to background
100
63
66
69
72
75
78
81
84
87
90
Re: [Bug] 4.2.1 Network config not loading
Sorry no. Actually I always create a pup_save through a controlled shut down before beginning any kind of testing.WhoDo wrote:Could this be because your pup_save file isn't created until you reboot? I don't know where these settings are stored in the RAM disk, but maybe that section isn't getting saved on first creation of the pup_save. Does it save ok for subsequent boots following creation of the pup_save file?DaveS wrote:4.2.1 frugal USB. Wifi Network configuration previously set up does not autoload at next boot and has to be set up via the wizard again.
Update: Pwireless finds my network and will log on to it if I go through the normal procedure. Also, Pwidgets shows my network as activated after re-boot, but my browser and email cannot access it until I configure it either through network wizard or pwireless.
Spup Frugal HD and USB
Root forever!
Root forever!
Re: [Bug] 4.2.1 Network config not loading
I don't think this is the case as least not for me as I had the same problem as reported above (frugal-HD) and I had created a save file. As mentioned earlier 420 was ok in this respect for me.WhoDo wrote:Could this be because your pup_save file isn't created until you reboot? I don't know where these settings are stored in the RAM disk, but maybe that section isn't getting saved on first creation of the pup_save. Does it save ok for subsequent boots following creation of the pup_save file?DaveS wrote:4.2.1 frugal USB. Wifi Network configuration previously set up does not autoload at next boot and has to be set up via the wizard again.
Rgds Mike
Re: [Bug] 4.2.1 Network config not loading
I found the same problem. I don't think it is hardware related. In addition to 421rc2 I have the following (frugal) puppies installed on the same computer:
upup461, NOP413, 420rc2, 42final
The first three reconnects to my WAN but the fourth does not. So there seems to have been a change in the Network Wizard script between 420rc2 and 42final.
Ecube
upup461, NOP413, 420rc2, 42final
The first three reconnects to my WAN but the fourth does not. So there seems to have been a change in the Network Wizard script between 420rc2 and 42final.
Ecube
Re: [Bug] 4.2.1 Network config not loading
The Network Wizard scripts in 420rc2 and 42final are identical. So the cause of the problem rests elsewhere. The 420 upgrade by ttuuxxx (v2) (where Pwidgets is removed) is OK.
Ecube.
Ecube.