xunil,

Again it depends on what you want to do - I do a lot of "bulk" resizing - generation of quick email resolutios etc. I have yet to find anything on Linux.

I do use Photoelf www.photoelf.com under WINE - it works fine and is just as fast under puppy as under WinXP

Alison

Hi, My Setup : Puppy 2.16, AMD 1.5Ghz Processor 1.5Gb RAM, Frugal install to HDD 1Gb file. I recently installed Firefox 2.0.0.1 from: http://dotpups.de/dotpups/Internet/ When I run Fireox it automatically downloaded and upgraded to 2.0.0.6 However I find it still has a few bugs * Crashes quite a lot ...

Puppy 2.16 / embedded VIA 500Mhz board / 1Gb CF Card in EDE adaptor Problem solved - for the benefit of anyone searching and finding this.... "Using Realvnc server with Tightvnc client" In real VNC client you enter the port number (normally beginning at 5900) - in TightVNC you enter the x term ...

I realise this is pretty boring but I instaled Firefox 2.0.0.1 from: http://dotpups.de/dotpups/Internet/ And it did all the default browser stuff for me - when I click on "Browse" FF starts rather than sea monkey... The only trick now is to get IE working under WINE so I can do my internet shopping ...

Hello and thanks for reading! I have an embedded system sucesfully runing VNC server - from RealVNC (windows or SuSe) when I try to connect I enter the address as: ip-address:5900+display e.g. 192.168.1.5:5901 for VNC server running on Xterm 1 on a machine with IP address 192.168.1.5 Puppy comes ...

Tallis,

One more question...

Does the drive work OK in say a Windows PC - I had this same problem with a 1Gb Microdrive on my work laptop (Win 2k, would take 5-10mins), a few weeks after it went slow the Microdrive stopped working altogether!

Alison

CMA, I had this problem myself with an old Fujitsu Laptop I had: 1 - Boots from floppy but only the "special" one that I don't have 2 - Will not boot from any form of USB 3 - Would not boot from PCMICA CD-ROM (but read more later...) As I still had windows 2000 running on the machine I used the ...

Tommy - I think the answers above give you two ways of doing it: /etc/rc.d/rc.local and .xinitrc However there is a third way - install a small autostart utility, see: http://murga-linux.com/puppy/viewtopic.php?search_id=1801045872&t=6084 I struggled for ageas to get VNCserver to start in my ...

This refers to Puppy 2.16
UPDATED : the sucess of my post above depends on which vieo server you select -

See:
http://murga-linux.com/puppy/viewtopic.php?t=20768
for more details

Micron, thanks this is most appreciated - I have now had some success - for anyone else reading this my situation is as follows: Using Xorg ======= It is possible to start VNC server automatically by adding the line vncserver:1 -geometry 1024x768 to the end of .xinitrc just vefore the exec jwm bit ...

I dont know What "TwinMOS 4gb 140x ... How did you format your CF card? Fat32? ex2? Did you change the mbr, or just leave it as it was? thanks, Magnus Magnus I have done this uing an old Tosh laptop (some time ago and don't have it any more dont remeber the version number) I definately remeber I ...

Hi Alison, I restart my puppy server remotley now, and without a monitor connected, and never get the wizard. I'm using Xversa. Micron - I am encouraged! (I also run Xvesa) Q1 : What Puppy version / system are you running Q2 : how are you starting VNC / connecting to the machine when not booted ...

Puppy universal installer permit install in ide flash drive (cf card in ide adaptor). How to find this flash hard disks? I'm in italy,i have read that this flash drive working as normal hard disk and have long time life. This is a solutions for older pc's,because new ide traditional hard disk ...

Hi I have sucesfully managed this and will share it - the trick (I think) is to start after the Xserver, but before the JWM windows manager... Refers to : Puppy 2.16 I editied the file /root/.xinitrc and added the line: vncserver :1 -geometry 1024x768 just before the end of the file. IMPORTANT learn ...

Hi, I have searched everywhere for this but can't find the answer... Embedded System : VIA MINI-ITX EPIA M 533 Mhz, 1Gb CF card in IDE adaptor, Puppy 2.16 I have sucesfully installed puppy, X works fine and I have managed to get VNC to start automatically by adding the line: vncserver :1 -geometry ...

Hi, first time posting I'm not a total newbee (used Unix before) but no expert.- I found this post the instructions above and got Citrix to work, as they are not too detailed (and I made some mistakes due to this) I though I would write some detailed instructions that worked for me... I have Puppy 2 ...