915resolution patched

[tempestuous]

915resolution just updated in the first post to support the HD Graphics 3000 device, device ID 0104:8086
as found in (some) Core i3/i5/i7 "Sandy Bridge" integrated processors.

[zubr]

az@az:~# 915resolution -l
Intel 800/900 Series VBIOS Hack : version 0.5.3

Unable to determine bios type.
Please run the program 'dump_bios' as root and
email the file 'vbios.dmp' to stomljen@yahoo.com.
Chipset: HD3000
Mode Table Offset: $C0000 + $142
Mode Table Entries: 39

[tempestuous]

Please run the program 'dump_bios' as root and
email the file 'vbios.dmp' to stomljen@yahoo.com.

That's probably what you will have to do. My package includes the "dump_bios" utility.

... or maybe upgrade to the very latest Xorg with updated intel driver.

[zubr]

Bios attached.

I use latest Xorg, but I cannot use Intel driver because after 2.9 version it works only with KMS, but FreeBSD still has no KMS support. Drivers before 2.9 version don't have support for Sandy.

So I have resolution 1024x768 instead of 1366x768 with VESA..

[haohetao]

My Computer
zotac H55ITX-A-E Wifi
intel core i3 530(2.66GHz)
HD Intel® HD Graphics (used in Intel® 2010 Core™ i7/i5/i3 processor family)

915resolution -l

Intel 800/900 Series VBIOS Hack : version 0.5.3

Intel chipset detected. However, 915resolution was unable to determine the chipset type.
Chipset Id: 408086
Please report this problem to stomljen@yahoo.com

lspci -mm -v -d 8086:0042

Slot: 00:02.0
Class: VGA compatible controller
Vendor: Intel Corporation
Device: Core Processor Integrated Graphics Controller
SVendor: Intel Corporation
SDevice: Core Processor Integrated Graphics Controller
Rev: 12

lspci -nn -vv -d 8086:0042

00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042] (rev 12) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at fb800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at dc00
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0500c Data: 4189
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: i915
Kernel modules: i915

[haohetao]

Hi,Why not have my graphics

[tempestuous]

haohetao, check your private messages!
7 days ago (July 20) I sent you an updated version of 915resolution to test.

[Samuel_Vimes]

I have the same problem with my dell inpiron N5110 =(

sudo ./915resolution -l

Intel 800/900 Series VBIOS Hack : version 0.5.3

Intel chipset detected. However, 915resolution was unable to determine the chipset type.
Chipset Id: 1048086
Please report this problem to stomljen@yahoo.com

lspci -mm -v -d 8086:0116

Slot: 00:02.0
Class: VGA compatible controller
Vendor: Intel Corporation
Device: Sandy Bridge Integrated Graphics Controller
SVendor: Dell
SDevice: Device 04ca
Rev: 09

lspci -nn -vv -d 8086:0116

00:02.0 VGA compatible controller [0300]: Intel Corporation Sandy Bridge Integrated Graphics Controller [8086:0116] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:04ca]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-

[rbeef]

I have a new Acer 4752-6431. I'm getting the following:

slippy$ sudo ./915resolution -l
Password:
Intel 800/900 Series VBIOS Hack : version 0.5.3

Unable to determine bios type.
Please run the program 'dump_bios' as root and
email the file 'vbios.dmp' to stomljen@yahoo.com.
Chipset: HD3000
Mode Table Offset: $C0000 + $142
Mode Table Entries: 39
slippy$

It sees the chipset but not the VBIOS. Can you help? I've uploaded my vbios.dmp file.

[vtpup]

Same problem here. I ran the 915 resolution patch .pet but got same result.
Error message below appears every boot. Racy 5.3 on an Acer Aspire 5349-2635 laptop)

Code: Select all

# 915resolution -l
Intel 800/900 Series VBIOS Hack : version 0.5.3

Unable to determine bios type.
Please run the program 'dump_bios' as root and
email the file 'vbios.dmp' to stomljen@yahoo.com.
Chipset: HD3000
Mode Table Offset: $C0000 + $142
Mode Table Entries: 39

# lspci
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)

The display is working, I don't know if the above error message ("Unable to......39") is significant, but is always appears on startup.

[01micko]

Newer xorgs, such as in Racy/Slacko/Dpup/Precise seem not to need 915resolution. I tried in Slacko development and I get nice widescreen on my laptops that have it including a small eee-701SD.

[vtpup]

I won't worry about the message, then. Thanks 01 micko.

[frontman]

Can someone host the patch? The download links aren't working for me.

[Semme]

Not werk'in? Plug'm with wget..

[01micko]

You mean the patched source? At Barry's source repo

http://bkhome.org/sources/alphabetical/ ... 617.tar.gz

You need the secret password (not so secret, look around)

[darwinev0lved]

Newer xorgs, such as in Racy/Slacko/Dpup/Precise seem not to need 915resolution. I tried in Slacko development and I get nice widescreen on my laptops that have it including a small eee-701SD.

what precisely are you / were you using ? I was trying to resurrect my eee-701 and have tried precise 5.5 and slacko 5.5 and in neither of them was I able to get the 800*480 resolution.

Also the download links to the pets are broken / dead - does anybody have working links ?

Regards,
Jon.

[ally]

hey darwin

there is an eee specific build which has everything working

puppeee1.0 available here: http://distro.ibiblio.org/puppylinux/Pu ... uppeee1.0/

just need to select correct one for processor

[darwinev0lved]

hey darwin

there is an eee specific build which has everything working

puppeee1.0 available here: http://distro.ibiblio.org/puppylinux/Pu ... uppeee1.0/

just need to select correct one for processor

thanks for the link Ally - I've actually got a version, I think it's Lucid 4.2 installed that works fine - I just fancied trying to update to see what the latest and greatest were like ... and actually I have success (Precise 5.5) - had to manually enter in the vertical & horizontal 30.61 & 60.61 and it came back with the 800*480 resolution. So all is fine - will see what else I can do with it. All is happy in eee-puppy land (till the next gotcha)

thanks again

J