pchan wrote:What could I have done wrong? Load bluetooth Tahr.sfs together perhaps?
rcrsn51 wrote:All you need to test this is a clean install of Tahrpup and the bluez-streaming PET by tempestuous.
Yes, I don't think the problem is related to a conflict with the wifi device.pchan wrote:# lsusb
Bus 006 Device 002: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
# hcitool scan
Device is not available: No such device
Code: Select all
hciconfig hci0 up
Code: Select all
hciconfig hci0 down
hciconfig hci0 reset
hciconfig hci0 up
Code: Select all
hcitool scan
I can confirm the following with my external adapter. If I run "hiconfig hci0 down", the adapter disappears from "hcitool dev" and nothing else works. Once I bring it back up, things start working again. Hopefully, that's all that pchan needs.tempestuous wrote:pchan, I wonder if you can't bring your USB interface to life just with this command -Code: Select all
hciconfig hci0 up
Code: Select all
#!/bin/sh
echo 0000 | bluez-simple-agent hci0 XX:XX:XX remove
aplay -D btheadset /usr/share/audio/2barks.wav
But not successful ...tempestuous wrote:tempestuous and rcrsn51,pchan wrote:
pchan, I wonder if you can't bring your USB interface to life just with this command -If that appears to fail, try these more comprehensive options -Code: Select all
hciconfig hci0 up
If any of that appears successful, go ahead and try -Code: Select all
hciconfig hci0 down hciconfig hci0 reset hciconfig hci0 up
Code: Select all
hcitool scan
NOTE : Testing done in LxTahr 14.12 no Pae (will try in Tahr 6.01 no pae testing tomorrow)
Okay. Some progress here.
I ran " hcicinfig hci0 up
Then
"Hcitool scan"
Scanning started ....
Located headset MAC (14:07:24:33:08:2A) !!!
Next
"bluez-simple-agent hci0 14:07:24:33:08:2A"
.................
.....................
.................
connection refused. (oh Oh!)
Triedtempestuous wrote: hciconfig hci0 piscan
bluetooth-agent 0000
then power-off / power-on your bluetooth receiver. Hopefully it will now show that it is paired.
It sounds like your bluetooth headset needs to authorise the pairing. Is there an instruction manual that came with that device? Maybe there's some particular button you need to press at that point?pchan wrote:"bluez-simple-agent hci0 14:07:24:33:08:2A"
.................
connection refused.
rcrsn51,rcrsn51 wrote:Code: Select all
#!/bin/sh echo 0000 | bluez-simple-agent hci0 XX:XX:XX remove aplay -D btheadset /usr/share/audio/2barks.wav
It might be that the authors of the smplayer gui failed to accommodate all possible options.pchan wrote:smplayer 14.9.0 > under preference > audio output > options to choose bluetooth headset never showed up.
Code: Select all
driver\audio_output=...
Code: Select all
driver\audio_output="alsa:device=bluetooth"
Thanks tempestuoustempestuous wrote: But you should be able to "hard-code" the smplayer configuration file - open /root/.config/smplayer/smplayer.ini in Geany, and find the line that starts with -change it to -Code: Select all
driver\audio_output=...
Make sure you include the quotation marks. Save.Code: Select all
driver\audio_output="alsa:device=bluetooth"
Thanks rcrn51, I added the default card 2 in my asound.conf.rcrsn51 wrote: In the post here there is an asound.conf with some "default" sections. It may work better for you. ...
btrepair.
rcrsn51 wrote:@pchan: Here is one more question. If you run your WiFi and BT streaming audio at the same time, is there any interference? Does that btcoexist package have any value?
gcmartin wrote:Would that tool and instructions be a 2-way transfer ability or one-way ability?
How can I answer questions about something that has not yet had an actual test with a phone?rcrsn51 wrote:However, it needs testing.
See above.And, assuming the script works in FATDOG, are the instructions steps the same?
rcrsn51,rcrsn51 wrote:How to Transfer Files using Bluetooth
This package is a companion to tempestuous' bluez_4.101-streaming.pet. It contains the tools for performing file transfers between Puppy and a remote BT device like a phone. However, it needs testing.
If you are interested, post a message and I will provide some instructions.
I installed the petrcrsn51 wrote:@pchan: I am sending you a PM.