Quirky Pyro64 version 0.6 (alpha) -- and Pyro32 0.5
- BarryK
- Puppy Master
- Posts: 9392
- Joined: Mon 09 May 2005, 09:23
- Location: Perth, Western Australia
- Contact:
ethernet still failing at first bootup.
At first bootup, /etc/rc.d/rc.sysinit calls /etc/rc.d/rc.network_eth, which tests if an ethernet interface is connected to the Internet and if so, runs 'dhcpcd'.
However, I found that recent linux kernels take an extraordinarily long time to create /sys/class/net/eth0. I had to put "sleep 6" into rc.network_eth, which is ok as the script is backgrounded.
However, I have just discovered that even 6 seconds may not be enough. Today I tested Easy Pyro64, and found that 7 seconds is required! -- that's on my fast midi-tower, with i5 CPU!
I have fixed /etc/rc.d/rc.network_eth, see attached.
I am wondering if there is some way of detecting, hey we have a ethernet interface, even before /sys/class/net/eth0 appears, then wait for however long it takes.
I also found that it takes a bit longer after /sys/class/net/eth0 appears, before "ifconfig -a" returns "eth0" -- don't know exactly how much delay.
At first bootup, /etc/rc.d/rc.sysinit calls /etc/rc.d/rc.network_eth, which tests if an ethernet interface is connected to the Internet and if so, runs 'dhcpcd'.
However, I found that recent linux kernels take an extraordinarily long time to create /sys/class/net/eth0. I had to put "sleep 6" into rc.network_eth, which is ok as the script is backgrounded.
However, I have just discovered that even 6 seconds may not be enough. Today I tested Easy Pyro64, and found that 7 seconds is required! -- that's on my fast midi-tower, with i5 CPU!
I have fixed /etc/rc.d/rc.network_eth, see attached.
I am wondering if there is some way of detecting, hey we have a ethernet interface, even before /sys/class/net/eth0 appears, then wait for however long it takes.
I also found that it takes a bit longer after /sys/class/net/eth0 appears, before "ifconfig -a" returns "eth0" -- don't know exactly how much delay.
- Attachments
-
- rc.network_eth.gz
- False .gz
- (2.4 KiB) Downloaded 184 times
[url]https://bkhome.org/news/[/url]
Pyro32 0,6.1 is good. Boots with six bracketed [...] Error calls invoking cpu0, but ignores them and continues to terminal. Set Radeon & res. -> complete DT with correct DHCP & sound running. For my purposes, this is all I desire, i.e. no wish to loop-the-loop with xyz HDs, USBs, w.h.y. - just need this bog std, fast, compact distro it always was. For teaching pigs to fly and dogs to bark, I use other machines with other FULL installs and all the bells & whistles loaded.
Puppy = K.I.S.S. Thank you.
Puppy = K.I.S.S. Thank you.
pyro64 0.6
With pyro64, didn't we have a bluetooth tool to set it up, I was sure it was there and working with 0.5, but can't find it anywhere with 0.6 and my mouse won't work without it with both a touchpad and mouse?
I had the same problems with pyro32 as I had with pyro64.
For instance I couldn't get a samba server to work -->
Apparently because I couldn't create a samba user.
For instance I couldn't get a samba server to work -->
Apparently because I couldn't create a samba user.
_________________________________________# smbpasswd -a don570
New SMB password:
Retype new SMB password:
Failed to add entry for user don570.
- BarryK
- Puppy Master
- Posts: 9392
- Joined: Mon 09 May 2005, 09:23
- Location: Perth, Western Australia
- Contact:
Right now, looking at fixing wcpufreq (if it needs it):
http://murga-linux.com/puppy/viewtopic. ... 262#976262
http://murga-linux.com/puppy/viewtopic. ... 262#976262
[url]https://bkhome.org/news/[/url]
Printing with Pyro32-0.6
G'day,
BarryK wrote:
On the other hand, I could 'print' pdfs by 'Export' from LibreOffice or using the "Print-to-file" in Printer 'Options' (see pdfs in /file in second screenshot) .
The CUPS.desktop file (screenshots) won't run for me if clicked - something about 'failed to execute child process' for a non-existent 'htmlview'?
Still liking Pyro32 as a Full Pup nonetheless.
David S.
BarryK wrote:
Still "saving the rain-forest trees" with my XP200 printer not wanting to use any paper when installed as a 'Local' printer via its usb socket (screenshot from CUPS).Can you test with a local printer?
Note, I don't think that missing "pdf-writer" matters. The print-to-file should still work.
On the other hand, I could 'print' pdfs by 'Export' from LibreOffice or using the "Print-to-file" in Printer 'Options' (see pdfs in /file in second screenshot) .
The CUPS.desktop file (screenshots) won't run for me if clicked - something about 'failed to execute child process' for a non-existent 'htmlview'?
Still liking Pyro32 as a Full Pup nonetheless.
David S.
- Attachments
-
- printer-localusb-filterfails.jpg
- Epson XP200 installed via USB still 'filter failed'
when trying to print test page - (141.51 KiB) Downloaded 486 times
-
- pdf-export-printtofile-OK.jpg
- Pdf printing OK via Export or 'Print-to-file' but no-go via Cups
- (39.86 KiB) Downloaded 481 times
-
- CUPS-in-desktop-directory.jpg
- Cups desktop file - clicking not effective - but Wizard in Menu is fine
- (65.98 KiB) Downloaded 488 times
-
- CUPS.desktop-text.jpg
- Cups desktop file text
- (79.1 KiB) Downloaded 488 times
- BarryK
- Puppy Master
- Posts: 9392
- Joined: Mon 09 May 2005, 09:23
- Location: Perth, Western Australia
- Contact:
Re: pyro64 0.6
Er, yes.scsijon wrote:With pyro64, didn't we have a bluetooth tool to set it up, I was sure it was there and working with 0.5, but can't find it anywhere with 0.6 and my mouse won't work without it with both a touchpad and mouse?
Two PET packages are missing, 'bluepup' (in noarch repo) and 'bluepup_tray' (was in xerus repo).
These will be in the next release.
[url]https://bkhome.org/news/[/url]
- BarryK
- Puppy Master
- Posts: 9392
- Joined: Mon 09 May 2005, 09:23
- Location: Perth, Western Australia
- Contact:
Looking at the docs on smbpasswd:don570 wrote:I had the same problems with pyro32 as I had with pyro64.
For instance I couldn't get a samba server to work -->
Apparently because I couldn't create a samba user.
_________________________________________# smbpasswd -a don570
New SMB password:
Retype new SMB password:
Failed to add entry for user don570.
https://www.samba.org/samba/docs/man/ma ... swd.8.html
'smbd' needs to be running. By default, this is not running. /etc/init.d/rc.samba starts it at bootup, however the script has its "exec" flags cleared, so doesn't run. This is a security precaution.
Set the exec flags and reboot. Um, no need to reboot, just run "/etc/init.d/rc.samba start"
EDIT:
I have never used samba. Strange, but true.
Anyway, looking at the docs, smbpasswd can only assign a password to an existing user. Trying an experiment:
Code: Select all
# smbpasswd -a don570
New SMB password:
Retype new SMB password:
Failed to add entry for user don570.
# adduser don570
adduser: /home/don570: No such file or directory
Changing password for don570
Enter the new password (minimum of 5, maximum of 8 characters)
Please use a combination of upper and lower case letters and numbers.
New password:
Re-enter new password:
passwd: password changed.
#
# smbpasswd -a don570
New SMB password:
Retype new SMB password:
Added user don570.
Asking the question though, as someone who has never used samba, why do you have to create a user "don570"? Aren't we running as root?
[url]https://bkhome.org/news/[/url]
To BarryK ...
Were you able to make a samba server work by connecting another linux computer using ethernet cable??
because I wasn't
________________________________________________
after 'root' user wouldn't connect with my other linux computer.
By the way here is the instructions for the new fatdog 720 by kirk
Were you able to make a samba server work by connecting another linux computer using ethernet cable??
because I wasn't
________________________________________________
I didn't read the instructions for samba and I was desperate for a connectionwhy do you have to create a user "don570"
after 'root' user wouldn't connect with my other linux computer.
By the way here is the instructions for the new fatdog 720 by kirk
_________________________________________________# A private directory example, usable only by kirk. Note that kirk must be a valid Linux user and a
# valid Samba user. To make this work open the control panel and click on the System tab. Then
# click on Fatdog64 User Manager. Click on the Add button and add a new user named "kirk". This will
# add kirk as a new user and create a home directory for kirk at /home/kirk. This directory will be
# owned by kirk. If you choose some other folder for kirk to share, make sure kirk owns that folder.
# Then open a terminal and type smbpasswd -a kirk. You'll be prompted for a new password. After that
# un-comment the section below and restart Samba.
[kirkdir]
comment = Kirk's Service
path = /home/kirk
valid users = kirk
public = no
writable = yes
printable = no
A pyro64 0.6 Bluetooth problem
Thanks for that, found them and they loaded but it seems that "something is not quite there" as they say.BarryK wrote:Er, yes.scsijon wrote:With pyro64, didn't we have a bluetooth tool to set it up, I was sure it was there and working with 0.5, but can't find it anywhere with 0.6 and my mouse won't work without it with both a touchpad and mouse?
Two PET packages are missing, 'bluepup' (in noarch repo) and 'bluepup_tray' (was in xerus repo).
These will be in the next release.
Data from PupSysinfo is:
VendorID=0bda ProductID=0821 Rev=02.00
Manufacturer=Realtek
Product=Blootooth Radio
SerialNumber=00e04c000001
Driver=btusb
and elsewhere
Kernel-Module=btusb
The drivers seem to be there, according to PupSysinfo
But using Bluepup gives "No default controller available", nor does it find any devices, and Bluepup command "discoverable on" says "no default controller available";
and "list" does nothing so I think it's not finding the realtek radio controller for some reason.
Could I have some help please from someone who knows about this "stuff" on where to go from here, as I know almost nothing about bluetooth being as most of my 'stuff' connects via ethernet.
thanks
@scsijon: Try "hciconfig" and report what you see.
A properly working bluetooth report this:
A properly working bluetooth report this:
Code: Select all
hci0: Type: BR/EDR Bus: USB
BD Address: XX:XX:XX:XX:XX ACL MTU: 1021:5 SCO MTU: 96:6
UP RUNNING PSCAN
RX bytes:1247 acl:0 sco:0 events:74 errors:0
TX bytes:1109 acl:0 sco:0 commands:74 errors:0
[/quote]
If you don't see "UP", try "hciconfig hci0 up". Perhaps you should also have another terminal open, running "dmesg -w" so you can see the error that the kernel spits out when you try to bring the interface up.
The report the rest to Barry, heh heh heh :twisted:
Fatdog64 forum links: [url=http://murga-linux.com/puppy/viewtopic.php?t=117546]Latest version[/url] | [url=https://cutt.ly/ke8sn5H]Contributed packages[/url] | [url=https://cutt.ly/se8scrb]ISO builder[/url]
thank you jamesbond for your guidance
replies are>
for hciconfig>
hci0: Type: Primary Bus: usb
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX Bytes:14 acl:0 sco:0 events:1 errors:0
TX bytes:3 acl:0 sco:0 events:1 errors:0
for hciconfig hci0 up>
Can't init device hc0: no such file or directory (2)
>and it's right there is no /dev/hci0, i wonder if I need to add it, but what should it's device settings be?
dmesg -w errors out as invalid option however dmesg results in>
[267.329010] Bluetooth: hci0: rtl: examining hci_ver=06 hci_rev=000a lmp_ver=06 lmp_subver=8821
[267.329026] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[267.329101] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[267.329113] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[267.329158] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[267.329167] Bluetooth: hcl0: Failed to load rtl_bt/rtl8821a_fw.bin
>So that explains a lot, it looks like it doesn't like that bin file
> and starting bluepup states (in the error log) Waiting to connect to bluetoothd... so maybe I have loaded the wrong pet, but I could only see one of them?
and nearly the same dmesg output (different line numbers) but three new ones first (from bluepup I take it)>
[1891.819142] Bluetooth: BNEP (Ethernet Emmulation) ver 1.3
[1891.819147] Bluetooth: BNEP filters: protocol multicast
[1891.819158] Bluetooth: BNEP socket layer initialized
[2000.680108] Bluetooth: hci0: rtl: examining hci_ver=06 hci_rev=000a lmp_ver=06 lmp_subver=8821
[2000.680124] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[2000.680201] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[2000.680214] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[2000.680259] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[2000.680268] Bluetooth: hcl0: Failed to load rtl_bt/rtl8821a_fw.bin
> over to you, it's time for sleep as it's 0145 in the morning here and i'm due up in five hours
regards to all
EDIT:it seems I needed to download and install the matching bluez as well? it now works
replies are>
for hciconfig>
hci0: Type: Primary Bus: usb
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX Bytes:14 acl:0 sco:0 events:1 errors:0
TX bytes:3 acl:0 sco:0 events:1 errors:0
for hciconfig hci0 up>
Can't init device hc0: no such file or directory (2)
>and it's right there is no /dev/hci0, i wonder if I need to add it, but what should it's device settings be?
dmesg -w errors out as invalid option however dmesg results in>
[267.329010] Bluetooth: hci0: rtl: examining hci_ver=06 hci_rev=000a lmp_ver=06 lmp_subver=8821
[267.329026] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[267.329101] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[267.329113] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[267.329158] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[267.329167] Bluetooth: hcl0: Failed to load rtl_bt/rtl8821a_fw.bin
>So that explains a lot, it looks like it doesn't like that bin file
> and starting bluepup states (in the error log) Waiting to connect to bluetoothd... so maybe I have loaded the wrong pet, but I could only see one of them?
and nearly the same dmesg output (different line numbers) but three new ones first (from bluepup I take it)>
[1891.819142] Bluetooth: BNEP (Ethernet Emmulation) ver 1.3
[1891.819147] Bluetooth: BNEP filters: protocol multicast
[1891.819158] Bluetooth: BNEP socket layer initialized
[2000.680108] Bluetooth: hci0: rtl: examining hci_ver=06 hci_rev=000a lmp_ver=06 lmp_subver=8821
[2000.680124] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[2000.680201] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[2000.680214] Bluetooth: hci0: rtl: loading rtl_bt/rtl8221a_config.bin
[2000.680259] Bluetooth hcl0: Direct Firmware Load for rtl_bt/rtl8221a_config.bin failed with error -2
[2000.680268] Bluetooth: hcl0: Failed to load rtl_bt/rtl8821a_fw.bin
> over to you, it's time for sleep as it's 0145 in the morning here and i'm due up in five hours
regards to all
EDIT:it seems I needed to download and install the matching bluez as well? it now works
Last edited by scsijon on Wed 13 Dec 2017, 07:13, edited 1 time in total.
Pyro32 0.6.1 FULL
[Preamble : found a little old 30Gb 1.8" HD, fittted printed-wiring adapter, scrubbed all the NTFS cr*p and formatted ext3/swap]
Did a FULL install. OK, but couple of points - no GRUB4DOS files available, even in PPM/refreshed, had to boot it off an old LUPU CD. Works - sound, DHCP, iPlayer/Flash - all ootb - fantastic. Little tray item claims cpu temp=79C - pure BS! I've done all this cpu temp thing at least a couple of times on the Forum. I know the laptop folks think they need it, (1) best advice is bin the laptop (2) ignore any claims about the cpu temp because no-one is clear where/what that relates to,(these days it's probably interpolated from an internal diode). An external thermocouple on one of those cheap digital voltmeters is probably what you need to know, ie it isn't going to catch fire/the fan is working (because you cleaned out the ducting last week!)/ because it's changes in T^oC between loaded & idle that provide more info about cpu health(and mode in multiple core devices). If there is overheating internally, chances are there's nothing you can do about it, subject to the usual precautions. Maybe ask about the precision of interconnect line-width on the fabricator's website, MTBF, warranty, etc?
Long & short : good deal, thanks.
[Preamble : found a little old 30Gb 1.8" HD, fittted printed-wiring adapter, scrubbed all the NTFS cr*p and formatted ext3/swap]
Did a FULL install. OK, but couple of points - no GRUB4DOS files available, even in PPM/refreshed, had to boot it off an old LUPU CD. Works - sound, DHCP, iPlayer/Flash - all ootb - fantastic. Little tray item claims cpu temp=79C - pure BS! I've done all this cpu temp thing at least a couple of times on the Forum. I know the laptop folks think they need it, (1) best advice is bin the laptop (2) ignore any claims about the cpu temp because no-one is clear where/what that relates to,(these days it's probably interpolated from an internal diode). An external thermocouple on one of those cheap digital voltmeters is probably what you need to know, ie it isn't going to catch fire/the fan is working (because you cleaned out the ducting last week!)/ because it's changes in T^oC between loaded & idle that provide more info about cpu health(and mode in multiple core devices). If there is overheating internally, chances are there's nothing you can do about it, subject to the usual precautions. Maybe ask about the precision of interconnect line-width on the fabricator's website, MTBF, warranty, etc?
Long & short : good deal, thanks.
- BarryK
- Puppy Master
- Posts: 9392
- Joined: Mon 09 May 2005, 09:23
- Location: Perth, Western Australia
- Contact:
It is about time that I actually used samba myself!don570 wrote:I tried to get the samba server to be recognized by a second computer and
it still fails to connect. Has anybody succeeded ?
__________________________________________________
I am going to install Open Media Vault, have downloaded the iso. This is a NAS operating system, based on Debian Stable.
Planning to install on my midi-tower PC, which has two ethernet sockets, 100MB/s and 1000MB/s. Then configure it as a Samba server.
[url]https://bkhome.org/news/[/url]
devx fails?
devx (devx-0.6-pyro64.pet) is failing to install, seems to copy/expand itself into /root first then fails with an error>
Error package devx-0.6-pyro64.pet failed to install.
xerrs.log shows>
stat: cannot stat '/root/devx-0.6-pyro64.pet': No such file or directory
expr:syntax error
expr:syntax error
/usr/local/petget/installpkg.sh: line175: [: -gt: unary operator expected
/usr/local/petget/installpkg.sh: line201: [: -gt: unary operator expected
I've tried d/l from 3 sites with the same result so i don't think it's me as other pets install ok
md5# is f06ba3a6ed3fa17c1945d78c57f755e1 if that helps
regards
EDIT: wierd, downloading from other puppies won't install,but downloading with PKGGet in pyro 0.6 works and injstalls.
Error package devx-0.6-pyro64.pet failed to install.
xerrs.log shows>
stat: cannot stat '/root/devx-0.6-pyro64.pet': No such file or directory
expr:syntax error
expr:syntax error
/usr/local/petget/installpkg.sh: line175: [: -gt: unary operator expected
/usr/local/petget/installpkg.sh: line201: [: -gt: unary operator expected
I've tried d/l from 3 sites with the same result so i don't think it's me as other pets install ok
md5# is f06ba3a6ed3fa17c1945d78c57f755e1 if that helps
regards
EDIT: wierd, downloading from other puppies won't install,but downloading with PKGGet in pyro 0.6 works and injstalls.
Last edited by scsijon on Wed 13 Dec 2017, 07:16, edited 1 time in total.
- technosaurus
- Posts: 4853
- Joined: Mon 19 May 2008, 01:24
- Location: Blue Springs, MO
- Contact:
If the kernel is configured with CIFS support, local "samba" shares can be mounted as follows:BarryK wrote:It is about time that I actually used samba myself!don570 wrote:I tried to get the samba server to be recognized by a second computer and
it still fails to connect. Has anybody succeeded ?
__________________________________________________
I am going to install Open Media Vault, have downloaded the iso. This is a NAS operating system, based on Debian Stable.
Planning to install on my midi-tower PC, which has two ethernet sockets, 100MB/s and 1000MB/s. Then configure it as a Samba server.
Code: Select all
mount -t cifs -o username=USERNAME,password=PASSWD,uid=$USER,gid=$USER //192.168.1.88/shares ~/mnt/share
Now if you've gone all out and want to resolve host names instead of using IP addresses directly, you'll also need "/sbin/request-key" (from keyutils IIRC) to resolve the IP for the kernel to use
To share files from Linux to Windows you'd still need the samba package for the server daemon, but for simple access to local Windows shares from Linux (probably ~90% of use cases), nothing else should be needed. Fortunately most routers and NAS devices will list the devices that are attached to it and the corresponding IP address on their UI (usually at 192.168.0.1/ for routers)
Extra info for developers. The kernel has a builtin keyring mechanism that it uses to store cached DNS resolutions (amongst other things) but no internal mechanism to resolve a hostname to an IP address; thus the need for /sbin/request-key (I don't get the reasoning behind using userspace tools from the kernel, but that's how it is) When you mount a remote SMB or CIFS share using the kernel's builitin filesystem, it will check to see if it is in //*.*.*.*/* format (not sure about IPv6 formatted addresses) and use IP addresses directly or make a call to dns_query to lookup the hostname. If it is already stored in the keyring, it uses the stored IP address to connect; otherwise it calls another builtin kernel function that calls /sbin/request-key. This is not unusual, /sbin/hotplug is used by the kernel to handle hot-plugging (though now most people use the netlink alternative these days) FWIW I experimented with my own DNS caching utility here, but it would need to be patched into the libc to really be helpful and Rich Felker didn't want to add it to musl since it is non-standard.
Check out my [url=https://github.com/technosaurus]github repositories[/url]. I may eventually get around to updating my [url=http://bashismal.blogspot.com]blogspot[/url].
probedisk -m doesn't work in some distros
probedisk -m doesn't work in some distros
BarryK has a script to install pyro64 to a drive i.e. a USB stick
pyro-0.5/4install-quirky-to-drive-mbr
it uses probedisk command
The script doesn't work in some distros because of probedisk -m
Here are some examples when I checked
(precise 571 and xerus worked) ...
Also see report
http://murga-linux.com/puppy/viewtopic. ... 803#976803
______________________________________________
BarryK has a script to install pyro64 to a drive i.e. a USB stick
pyro-0.5/4install-quirky-to-drive-mbr
it uses probedisk command
Code: Select all
echo "These are all of the drives found in your PC:"
INFODRIVES="$(probedisk -m | sed -e 's%/dev/%%')"
Here are some examples when I checked
(precise 571 and xerus worked) ...
Code: Select all
_____________________________________________________
echo "These are all of the drives found in your PC:"
INFODRIVES="$(probedisk -m | sed -e 's%/dev/%%')"
____________________________________________
xerus64 russian
# probedisk -m
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|drive|ATA Hitachi HUA72101
/dev/sdc|usbdrv|KingstonDataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
# probedisk
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|drive|ATA Hitachi HUA72101
/dev/sdc|usbdrv|KingstonDataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
_____________________________________________
precise 571
probedisk -m
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|usbdrv|KingstonDataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
# probedisk
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|usbdrv|KingstonDataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
___________________________________________
xenialpup 64 7.5
root# probedisk -m
* probedisk -m: unknown option. type 'probedisk -help'
root# probedisk
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|usbdrv|Kingston DataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
______________________________________________
slacko64 700
# probedisk -m
-m: invalid device
# probedisk
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|usbdrv|Kingston DataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
#
_____________________________________________
Dpup stretch 700a2
# probedisk -m
* probedisk -m: unknown option. type 'probedisk -help'
# probedisk
/dev/sda|drive|ATA SAMSUNG HD103SJ
/dev/sdb|usbdrv|Kingston DataTraveler 2.0
/dev/sr0|optical|SAMSUNG DVD-ROM SD-616E
___________________________________
http://murga-linux.com/puppy/viewtopic. ... 803#976803
______________________________________________
Last edited by don570 on Mon 11 Dec 2017, 22:56, edited 1 time in total.