(old)Puppy Linux Discussion Forum

that no right cilck paste is possible in terminal or console

To paste.
Click (push down) the scroll wheel, if the mouse has one, also works.

To copy just highlight.

Thank you Semme for your reply.
I am using 3g usb external modem which is automatically recognized and ready to use by tahr pup .

Thank you so much bigpup copy paste working now
What about the "bitmeteros" its not working, Is their any other pet to see internet use. Thanks again.

Is Tahr's firewall on (green)?

PTU, type: ifconfig into your terminal and hit enter.

There may be an "eth0," a "lo" and, or perhaps a "ppp0."

"How" is your connection seen?

no firewall is off (red)
ifconfig shows ppp0

Now type: netstat -l << Lowercase "L"

Doe the output include?

I attach what showing after netstat

Paste this into your terminal: ps aux > ~/ps_report.txt

You'll find it in /root where you can copy'n paste the results into this page.

Leave the link..

I've got the feeling its services aren't running.

And if this is the case, run: bmdb webstart and hit enter.

Is the browser PaleMoon?

you are right I was not running bitmeteros while netstat -l run on terminal, so sending new pic after running bitmeteros and then netstat -l

Sooo, does it work?

You should be able to reach this >> http://localhost:2605/index.html

yes browser palemoon
pastebin saying spam detected so cant attach ps report txt link.
pasting one line from ps report txt

(root 683 17.3 8.9 388240 91028 ? Sl 21:58 1:29 palemoon http://localhost:2605)


yes I am able to reach >> http://localhost:2605/index.html , but nothing showing in the graph.

Did you install LXTerminal?

No? Do it.

==

For PasteBin it's >> "New paste," then scroll down to the bottom and hit "Create new paste."

After the page loads grab the link from the address bar.

==

Here, does this return output with "bscapture" in its line? This definitely has to do with how BM sees your modem..

==

Hey WatchDog, you run a modem, correct?

Post if you can determine the holdup..

You know, I'll bet you need usb_modeswitch. I'll be back..

Do me a favor when you catch up.. Run: lsusb << A lowercase "L" starts this..

Then highlight the line for your modem, minimize the terminal, then center-clk to paste if you haven't yet installed LXTerminal.

==

PS -- You have one of these? >> /var/log/bitmeter/error.log

now I install LXTerminal
here is the link from pastebin >> http://pastebin.com/5CHgas9h

ps | grep bscapture return this >> 17260 root 0:00 grep bscapture


lsusb return this >> Bus 001 Device 006: ID 12d1:1436 Huawei Technologies Co., Ltd. E173 3G Modem (modem-mode)


"/var/log/bitmeter/error.log" not present

Nice work Mate.

With LXTerminal you can not only copy'n paste much easier, but it's easy to control fonts, sizing and colors.

==

I've seen your PasteBin and bscapture return -- good.

The lsusb dump gives us your Huawei device ID >> [12d1:1436] << Good!

No error log confirms my hunch.. That it's not an issue with BitMeterOS.

==

While I do a little investigation, I'd like you to confirm the steps you took to connect with Tahr.

It was "Internet Connection Wizard," then "Dialup analog or wireless modem," correct?

yes right, It was "Internet Connection Wizard," then "Dialup analog or wireless modem," One interesting thing about tahr is that it automatically detect it as 3G usb modem but other like in lucid puppy, i need to configure it manually.

How are you booting Pup? Off a stick or CD? 32 0r 64? CD would be good so we can try an alternative method..

I have done frugal install, 32 bit
As far as I know bit meter os 0.7.6 is stable version and 0.8.0 is experimental version and tahr quick pet bit meter os is 0.8.0 version. So may be it has some bug that need to sort out.

Do you have a burned CD?