Hi there. Im trying to install Puppy Linux on a Premier Netbook. When it is initializing there are not any problem in text mode. But when it tries to load video mode, appears something like this:
What should i do? Please help.
I have a VIA/S3G UniChrome Pro II video card.
Slacko has a problem with Premier Netbook video
Sorry, I tried to run slacko 5.6 non pae and specifications for this netbook are:
CPU: VIA C7, 1600 MHz.
Motherboard: VIA CX700 RCC Nbx 8010.
Video card and 3D Accelerator: VIA/S3G UniChrome Pro II.
Audio card: Realtek ALC662 @ VIA CX700/VX700.
IDE Controller: VIA Bus Master IDE Controller - 5324.
HDD: WDC WD800BEVS-00VAT0 (80 GB, 5400 RPM, SATA).
BIOS: American Megatrends Inc. ver. 080014.
Thank you for reply.
CPU: VIA C7, 1600 MHz.
Motherboard: VIA CX700 RCC Nbx 8010.
Video card and 3D Accelerator: VIA/S3G UniChrome Pro II.
Audio card: Realtek ALC662 @ VIA CX700/VX700.
IDE Controller: VIA Bus Master IDE Controller - 5324.
HDD: WDC WD800BEVS-00VAT0 (80 GB, 5400 RPM, SATA).
BIOS: American Megatrends Inc. ver. 080014.
Thank you for reply.
How are you booting Slacko?
From what?
This is probably a graphics driver issue.
Try to see if the Vesa driver will work.
It will usually work with any graphics hardware.
If you can get Puppy to boot to a prompt.
Run Xorgwizard.
Type xorgwizard at the prompt.
Select the vesa driver.
set resolution.
(pick one you know should work)
run test to see if it works.
finish xorgwizard.
back at prompt.
Type xwin
should see desktop.
From what?
This is probably a graphics driver issue.
Try to see if the Vesa driver will work.
It will usually work with any graphics hardware.
If you can get Puppy to boot to a prompt.
Run Xorgwizard.
Type xorgwizard at the prompt.
Select the vesa driver.
set resolution.
(pick one you know should work)
run test to see if it works.
finish xorgwizard.
back at prompt.
Type xwin
should see desktop.
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
While using xorgwizard.
Try resolution of
800x600
Try to also change the refresh frequency.
Try 60 or 70 refresh..
Set resolution.
Select test.
Select test X now.
After test results - select OK.
Select tweak.
Select tweak_xorg.conf
Select tweak_refresh
Scroll up or down ( some selections you will not see without scrolling)
High-lite desired refresh
Select OK
Select test X now.
Try resolution of
800x600
Try to also change the refresh frequency.
Try 60 or 70 refresh..
Set resolution.
Select test.
Select test X now.
After test results - select OK.
Select tweak.
Select tweak_xorg.conf
Select tweak_refresh
Scroll up or down ( some selections you will not see without scrolling)
High-lite desired refresh
Select OK
Select test X now.
The things they do not tell you, are usually the clue to solving the problem.
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
When I was a kid I wanted to be older.... This is not what I expected
YaPI(any iso installer)
I have similar so know nothing about them.VIA/S3G UniChrome Pro II.
try websearching for modelines for it...thought openchrome had got past these problems by now unless you are trying an old version of puppy?
When searching use the machine name and linux...you will doubtless find other frustrated users.
mike
Thank you very much!!, it worked enough to intall puppy in that netbook, but later shows the same problem at very first start of Slacko. I guess i need to edit config file on Slacko already installed in the netbook. At this moment i couldn't do this because a problem with the battery charger.bigpup wrote:While using xorgwizard.
Try resolution of
800x600
Try to also change the refresh frequency.
Try 60 or 70 refresh..
Set resolution.
Select test.
Select test X now.
After test results - select OK.
Select tweak.
Select tweak_xorg.conf
Select tweak_refresh
Scroll up or down ( some selections you will not see without scrolling)
High-lite desired refresh
Select OK
Select test X now.
Any novelty i will post it. Again, Thank you!!!