Hi Barry,
I have two different USB wi-fi , zd1211rw (old) and rtl8187(new buy). They both could not connect my AP (WEP) in the Wary with kernel 2.6.31.14.
I tested both USB wi-fi with different kernel 2.6.30.5, 2.6.33.2, ... in Wary/Quirky/Puppy, they work very good.
When dmesg, I found "wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate", is it have any different in kernel 2.6.31.14 .config ?
Hope tempestuous have some idea.
Thanks,
CHLee
zd1211rw:
Code: Select all
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
usb 1-2: reset high speed USB device using ehci_hcd and address 2
phy0: Selected rate control algorithm 'minstrel'
zd1211rw 1-2:1.0: phy0
usbcore: registered new interface driver zd1211rw
usb 1-2: firmware: requesting zd1211/zd1211b_ub
usb 1-2: firmware: requesting zd1211/zd1211b_uphr
zd1211rw 1-2:1.0: firmware version 4725
zd1211rw 1-2:1.0: zd1211b chip 0ace:1215 v4810 high 00-19-e0 UW2453_RF pa0 -7---
cfg80211: Calling CRDA for country: DE
wlan0: authenticate with AP 00:26:5a:43:eb:e4
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
wlan0: authenticate with AP 00:26:5a:43:eb:e4
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
wlan0: authenticate with AP 00:26:5a:43:eb:e4
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
rtl8187:
Code: Select all
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
phy0: Selected rate control algorithm 'minstrel'
phy0: hwaddr 08:10:74:b7:e3:54, RTL8187BvE V0 + rtl8225z2
rtl8187: Customer ID is 0x00
Registered led device: rtl8187-phy0::tx
Registered led device: rtl8187-phy0::rx
usbcore: registered new interface driver rtl8187
wlan0: authenticate with AP 00:26:5a:43:eb:e4
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
wlan0: direct probe to AP 00:26:5a:43:eb:e4 try 1
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
wlan0: authenticate with AP 00:26:5a:43:eb:e4
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate